科学の箱

科学・IT・登山の話題

Cisco

EAPOLのデバッグ

投稿日:

EPA2-Enterpriseで認証がうまくいかない。WLCでデバッグをかけた結果が以下の通り。

*Dot1x_NW_MsgTask_4: Aug 30 02:48:42.983: a4:4e:31:ce:80:4c dot1x – moving mobile a4:4e:31:ce:80:4c into Connecting state
*Dot1x_NW_MsgTask_4: Aug 30 02:48:42.983: a4:4e:31:ce:80:4c Sending EAP-Request/Identity to mobile a4:4e:31:ce:80:4c (EAP Id 1)
*apfMsConnTask_3: Aug 30 02:48:46.503: a4:4e:31:ce:80:4c Processing assoc-req station:a4:4e:31:ce:80:4c AP:00:78:88:29:9a:00-00 thread:15148740
*apfMsConnTask_3: Aug 30 02:48:46.503: a4:4e:31:ce:80:4c Association received from mobile on BSSID 00:78:88:29:9a:17 AP CNORDIBJSCN01AP002
別のラップトップで実施した結果が以下の通り。
*Dot1x_NW_MsgTask_4: Aug 30 02:51:41.937: 58:94:6b:22:88:04 dot1x – moving mobile 58:94:6b:22:88:04 into Connecting state
*Dot1x_NW_MsgTask_4: Aug 30 02:51:41.937: 58:94:6b:22:88:04 Sending EAP-Request/Identity to mobile 58:94:6b:22:88:04 (EAP Id 1)
*Dot1x_NW_MsgTask_4: Aug 30 02:51:41.983: 58:94:6b:22:88:04 Reset the reauth counter since EAPOLSTART has been received!!!
*Dot1x_NW_MsgTask_4: Aug 30 02:51:41.983: 58:94:6b:22:88:04 reauth_sm state transition 1 —> 1 for mobile 58:94:6b:22:88:04 at 1x_reauth_sm.c:47
*Dot1x_NW_MsgTask_4: Aug 30 02:51:41.983: 58:94:6b:22:88:04 Received EAPOL START from mobile 58:94:6b:22:88:0

EAP request/idenitityを送ると、eapol startがクライアントから送られてくるのが正しい処理。おかしいプロセスではクライアントは再度 associationを送ってくる。まるでEAP-request/identifyが送られてこないかのように。

 

メタ情報

inarticle



メタ情報

inarticle



-Cisco

執筆者:


comment

メールアドレスが公開されることはありません。 * が付いている欄は必須項目です

関連記事

no image

ダイヤルナンバーからルートグループまでのプロセス

ユーザーが番号を入力してからルーティングされるまでのプロセスは下記のページで詳しく説明されている。 Understanding Route Plans ユーザーがダイヤルをするとまず紐づいているCSS …

no image

SIPトランク

SIPトランクの設定 in VGW dial-peer voice 101 voip description SIP TRUNK to CUCM preference 1 destination-pa …

no image

PoEについて-2

Power Fan Inline Supply Model No Type Status Sensor Status —— —————- ——— ——- …

no image

CUCM License

  CUCMのライセンスを見ると、現在の持っているライセンスの数、割り当て済みライセンス、フリーライセンスがわかる。 フリーライセンス=現在持っているライセンス – 割り当て済み …

no image

ASAでファクトリリセット

ASAがどうにもならなくなったらファクトリリセットをかける。ファイル→Factory resetで可能である。 リセットする際には次にアクセスするときのIPアドレスを設定すること。 また構成をTFTP …

2016年9月
« 8月   10月 »
 1234
567891011
12131415161718
19202122232425
2627282930  

side bar top



アーカイブ

カテゴリー